vibrava
Journal Audio Guide

A Practical Guide to Monitoring and Mixing Speech for Broadcast

Priya Sandhu

6 min read

How to set up headphone monitoring, balance levels and check a speech mix on air and in the room, with steps a small crew can follow before every recording or transmission.

A Practical Guide to Monitoring and Mixing Speech for Broadcast

Start with what the listener will hear

Most audio problems on a broadcast are decided before anyone touches a fader. The first question is where the sound will be heard: through television speakers in a living room, through headphones on a phone, or through a public address system in a hall. Each of these forgives different faults. A thin voice survives a large PA but disappears on a small television speaker, while a boomy voice sounds warm in a studio and muddy on a laptop.

I begin every job by writing down the listening situations in one short note and sharing it with the producer. That note shapes microphone choice, where the monitoring sits and how much processing the mix needs. It also stops arguments later, because everyone has agreed what clear speech means for this particular programme and audience before rehearsals begin.

Set up monitoring you can trust

Monitoring is the part of audio engineering that gets the least attention and causes the most trouble. If you cannot trust what you hear, every decision after that is a guess. In a control room, place the speakers so that the engineer sits at the point where both reach the ears evenly, and keep them away from walls that add bass. Set one comfortable listening level and leave it alone, so that levels on the meters are judged against a steady reference.

Headphones are a second opinion, not a replacement. Closed-back pairs let you catch handling noise, plosives and mains hum that speakers hide. Before a recording, play a familiar piece of speech through the whole chain and listen for anything odd. Ten minutes spent here saves an hour of repair work during editing, and it shows the whole crew what normal sounds like.

Place microphones for the speaker, not the stand

Good placement starts with the person. A presenter who moves and gestures needs a different arrangement from a panel guest sitting still behind a table. Lavalier microphones suit movement, but clothing noise and chest resonance need care, so we test them with the real wardrobe rather than a sample jacket. Handheld and desk microphones give a steadier tone but depend on the speaker keeping a regular distance.

Whichever type is chosen, aim for the shortest practical distance and keep it consistent. Listen for room reflections from hard surfaces, because a hard table or glass wall will colour the voice more than any microphone model. A small piece of felt on a table, or a slight change of seating angle, often fixes what an equaliser cannot. Mark positions with tape so that rehearsal and transmission match.

Build a mix in simple, repeatable steps

A clean speech mix is built in a fixed order. First set the gain on each microphone so that normal speech sits comfortably below the loudest peaks, leaving headroom for a sudden laugh or raised voice. Then remove what does not belong: a gentle high-pass filter takes out rumble and handling noise without touching the voice. Only after that should compression and equalisation come in, in small amounts, and always judged against the reference voice.

Resist the urge to make everything loud. Consistency matters more than volume, because viewers adjust their own controls but cannot fix a voice that swings between whisper and shout. Where several people speak, bring down the microphones that are not in use so that room sound and spill do not pile up. Save the settings for each rehearsal so you can return to a known good starting point.

Check the sound in the room as well as on air

On live events the sound in the hall and the sound on the broadcast are two separate mixes that influence each other. Loudspeakers in the room can feed back into microphones and bleed into the broadcast, so agree early with whoever runs the room sound where the feeds are split. A clean feed taken before the room processing usually gives a better broadcast mix than a signal taken from the house desk.

During rehearsal, walk the room while someone speaks and listen at the back, at the sides and near the cameras. Then listen to the broadcast output on small speakers and on headphones. If speech is clear in all of those places, the mix is probably sound. If one position fails, note it and adjust rather than assuming the problem belongs to the audience's equipment.

A short routine for the day itself

On the day, a fixed routine keeps nerves out of the mix. Arrive early enough to check every microphone and cable, replace batteries on wireless units rather than trusting last week's, and run a line check from each position. Record a short test of each speaker saying their name and a sentence, then play it back through the monitoring. Mistakes are far easier to correct at this point than once the programme has begun.

Keep a printed list of settings, input names and fallback options near the desk. If a microphone fails, you should know in advance which spare replaces it and who is responsible for swapping it. After transmission, listen back to a few minutes of the recording and note anything to change next time. Over several productions this habit does more for sound quality than any new equipment.

Clear audio comes from habits rather than equipment: knowing where the sound will be heard, trusting your monitoring, placing microphones with care and mixing in a steady order. None of this needs a large crew, only a plan agreed with the producer and a routine repeated before every recording. If you are preparing a programme or event this winter, a short conversation about your listening situation and microphone positions is a sensible first step.

vibrava

Broadcast production from Chester: studio camera systems, lighting design, audio engineering and workflow planning for television, live broadcasts and events across the North West.

14 Watergate Mews, Chester CH1 2HU01244 355 718hello@vibrava.info